Simple AC voltmeter

-
I had long been thinking of designing a simple AC voltmeter but had somehow never gotten to it. However, with school just ending, and me going back to electronics, this was a neat simple yet useful circuit that I felt I could just get done with in a day or two.

The concept is fairly straight forward. Since I needed this only to measure the mains AC voltage and the output voltage of the sine wave inverter I was working on (based on the PIC32MX250F128B - more on this later), I didn't need to do any "true RMS" measurement. All I had to do was to convert the mains AC to DC, filter it and measure the peak voltage. Of course this had to be scaled down to a safe range for the microcontroller. The RMS voltage for a sine wave is equal to 0.707 (to 3 decimal places) the peak voltage.

The design was based on the Microchip PIC16F676. However I realized that I didn't have any in stock with me. So, I just used the pin-compatible PIC16F684. On the software side of things, the difference between the code for PIC16F676 and PIC16F684 is just one line. (See source file attached below.)

The variable resistor is adjusted so that the reading of my AC voltmeter matches that of a commercial voltmeter (Extech MA640 DMM). This is a sort of calibration.

CAUTION: THIS CIRCUIT IS NOT ISOLATED FROM THE MAINS AC AND HAS THE POTENTIAL TO BE LETHAL. YOU MUST BE VERY CAREFUL IF YOU ARE GOING TO USE THIS DESIGN. DO NOT ATTEMPT IF INEXPERIENCED. I CANNOT AND WILL NOT BE HELD RESPONSIBLE FOR ANY DAMAGE DONE WHILE USING THIS CIRCUIT.

Here's the schematic:

 Fig. 1 - Voltmeter

Here are some pictures:

 Fig. 2 - The PCB without (above) and with (below) the transformer


Fig. 3 - The test setup


Fig. 4 - Measuring voltage set with the variac


 Fig. 5 - Measuring voltage set with the variac


 Fig. 6 - Measuring voltage set with the variac

Fig. 7 - Measuring voltage set with the variac


C source file:
https://drive.google.com/file/d/0B4SoPFPRNziHdDB6cDdzNGZPdXc/edit?usp=sharing

http://www.4shared.com/file/Cz56s9Zlba/ACvoltmeter.html

mikroC project file:
https://drive.google.com/file/d/0B4SoPFPRNziHN2MydDRDalRWS1k/edit?usp=sharing
http://www.4shared.com/file/JwW3bpJNce/ACvoltmeter.html

Parts list (Excel XLSX file):
https://drive.google.com/file/d/0B4SoPFPRNziHb2ZCcnFNVnNpc2s/edit?usp=sharing
http://www.4shared.com/file/b_NcW4vdce/parts_list.html

Schematic (ARES DSN file):
https://drive.google.com/file/d/0B4SoPFPRNziHb1NFWDdwcWpJV2M/edit?usp=sharing
http://www.4shared.com/file/U6kPQH_rce/schematic.html

PCB (ARES LYT file):
https://drive.google.com/file/d/0B4SoPFPRNziHNDhhMDBkNFlnWW8/edit?usp=sharing
http://www.4shared.com/file/ZVczMJ7Wba/schematic.html

PCB (PDF files):
https://drive.google.com/file/d/0B4SoPFPRNziHMV9LdTBab1BXeDg/edit?usp=sharing
Mirrored:  https://drive.google.com/file/d/0B4SoPFPRNziHSmxvT1pSbXBWOTA/edit?usp=sharing

It's a fun simple yet useful project that you can build pretty easily if you want. Let me know what you think in the comments section below!

Comments

  1. sukhpreet singhMay 6, 2020 at 3:14 AM

    i have try too many times to generate a hex file.But it always show error that "MAIN FUNCTION IS NOT DEFINED". can u send me the hex file

    ReplyDelete

Post a Comment

Popular posts from this blog

N-Channel MOSFET High-Side Drive: When, Why and How?

-
Image
I had previously shown how to drive N-channel MOSFETs in low-side configuration. You can find the tutorial here: http://electel.blogspot.com/2016/12/low-side-mosfet-drive-circuits-and_23.html I’ve been requested to write a tutorial/article regarding high-side MOSFET drive. So, here I’ll talk about N-channel MOSFET high-side drive. Let’s first look at the common low side configuration.  Fig. 1 - N-channel MOSFET configured as low-side switch Now let’s look at a MOSFET configured as a high-side switch. Fig. 2 - N-channel MOSFET configured as high-side switch You can quite easily see the difference between the high-side configuration and the low-side configuration. In the low-side configuration, the load is connected between the drain and +V, while the source is connected to ground. Thus, the gate drive is referenced to ground. So by applying a voltage of >7V (for Power MOSFETs) or >4V (for Logic Level MOSFETs), the MOSFET can be fully turned on. Now let’s talk about the high-si...
Read more

Using the high-low side driver IR2110 - explanation and plenty of example circuits

-
Image
In many situations, we need to use MOSFETs configured as high-side switches. Many a times we need to use MOSFETs configured as high-side and low-side switches. Such as in bridge circuits. In half-bridge circuits, we have 1 high-side MOSFET and 1 low-side MOSFET. In full-bridge circuits we have 2 high-side MOSFETs and 2 low-side MOSFETs. In such situations, there is a need to use high-side drive circuitry alongside low-side drive circuitry. The most common way of driving MOSFETs in such cases is to use high-low side MOSFET drivers. Undoubtedly, the most popular such driver chip is the IR2110. And in this article/tutorial, I will talk about the IR2110. You can download the IR2110 datasheet from the IR website. Here's the download link: www.irf.com/product-info/datasheets/data/ir2110.pdf First let’s take a look at the block diagram and the pin assignments and pin definitions (also called lead assignments and lead definitions): Fig. 1 - IR2110 block diagram (click on image to enlarge)...
Read more

Using the SG3525 PWM Controller - Explanation and Example: Circuit Diagram / Schematic of Push-Pull Converter

-
Image
PWM is used in all sorts of power control and converter circuits. Some common examples include motor control, DC-DC converters, DC-AC inverters and lamp dimmers. There are numerous PWM controllers available that make the use and application of PWM quite easy. One of the most popular of such controllers is the versatile and ubiquitous SG3525 produced by multiple manufacturers – ST Microelectronics, Fairchild Semiconductors, On Semiconductors, to name a few. SG3525 is used extensively in DC-DC converters, DC-AC inverters, home UPS systems, solar inverters, power supplies, battery chargers and numerous other applications. With proper understanding, you can soon start using SG3525 yourself in such applications or any other application really that demands PWM control. Before going on to the description and application, let’s first take a look at the block diagram and the pin layout. Pins 1 (Inverting Input) and 2 (Non Inverting Input) are the inputs to the on-board error amplifier. If you a...
Read more