Car Cooling || Car Cooling Accessories || Car Cooling Fan Not Working || Car Cooling System Diagram

-


Car cooling system have a more component for provide engine cooling frequently and do your journey easy and comfortable


  •    
    Car cooling system is a most important part of car health, car cooling system control the engine tempareture at different conditions and it will be also help for car a/c system
    Coolant
  •    Radiator
  •    Electric Fan ( either fluid coupling)
  •    Thermostat valve
  •    Coolant pipelines or hosses
  •    Coolant reservoir
  •    Coolant tempareture sensor
  •    Overheating Malfunction light
  • COMPONENTS ARE
       Cylinder block (Engine)
  •    Water pump

 

Coolant

It is liquid type and it is a another name like long life coolant,Super long life coolant etc as per manufacturer recommended
Coolant have a some ingredients:Anti-freez, Glycol Ethylene propylene based,protects your engine from freezing while defending components against corrosion 🚙

Radiator

It is main part of car cooling system,it's working principle are- High pressure high tempareture engine outlets coolant convert to low pressure low tempareture coolant help of atmospheric air which are ready for inlet in engine🚙

Electric Fan

It's a part of vehicle for A/C and engine cooling systems,it's work basically when engine coollant tempareture above in standard tempareture these time that fan are rotated in opposite direction,because this fan are work in pulling  method (Air)🚙

Thermostat valve

Thermostat valve opening time is when coolant temperature is 82° this time thermostat valve are start for open and when the temperature is 90° above this time these valve are open fully and cooling the engine block and reduce heat🚙

Coolant pipes and hoses

Coolant pipes and hosses is part of car which provide coolant from one area to another area for easy to circulate and these hosses are clipping in high tension clip for leakage purpose

Coolant reservoir is a another important part of vehicle which check Preoditically the level of coolant because if any leakage in this system this part are show these because reservoir have mark like low or high🚙


WATER PUMP
It is part or cooling system that's are circulated the coolant from car v-belt or  drive belt🚙


Coolant temperature sensor

Coolant temperature sensor it is a part of vehicle which provide how many tempareture coolant on your car and if coolant tempareture is more than standard level this sensor are warning you for stop the vehicle instant🚙
Over heating Malfunction light
This is a warning light digitally warned you for overheating

Cylinder block

Block have a coolant line for realease heat
It's have a path where coolant are circulate frequently

Coolant is changeble part of car  at a standard kilometre,

Some car coolant replace in    20kSome car are coolant replace  80kSome car are coolant replace  160k 

  Totally depended on manufacturer recommended

Coolant basically two colours variable

1) RED
2)GREEN

Comments

Post a Comment

Popular posts from this blog

Using the TLP250 Isolated MOSFET Driver - Explanation and Example Circuits

-
Image
I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well
Read more

Using the SG3525 PWM Controller - Explanation and Example: Circuit Diagram / Schematic of Push-Pull Converter

-
Image
PWM is used in all sorts of power control and converter circuits. Some common examples include motor control, DC-DC converters, DC-AC inverters and lamp dimmers. There are numerous PWM controllers available that make the use and application of PWM quite easy. One of the most popular of such controllers is the versatile and ubiquitous SG3525 produced by multiple manufacturers – ST Microelectronics, Fairchild Semiconductors, On Semiconductors, to name a few. SG3525 is used extensively in DC-DC converters, DC-AC inverters, home UPS systems, solar inverters, power supplies, battery chargers and numerous other applications. With proper understanding, you can soon start using SG3525 yourself in such applications or any other application really that demands PWM control. Before going on to the description and application, let’s first take a look at the block diagram and the pin layout. Pins 1 (Inverting Input) and 2 (Non Inverting Input) are the inputs to the on-board error amplifier. If you a
Read more

N-Channel MOSFET High-Side Drive: When, Why and How?

-
Image
I had previously shown how to drive N-channel MOSFETs in low-side configuration. You can find the tutorial here: http://electel.blogspot.com/2016/12/low-side-mosfet-drive-circuits-and_23.html I’ve been requested to write a tutorial/article regarding high-side MOSFET drive. So, here I’ll talk about N-channel MOSFET high-side drive. Let’s first look at the common low side configuration.  Fig. 1 - N-channel MOSFET configured as low-side switch Now let’s look at a MOSFET configured as a high-side switch. Fig. 2 - N-channel MOSFET configured as high-side switch You can quite easily see the difference between the high-side configuration and the low-side configuration. In the low-side configuration, the load is connected between the drain and +V, while the source is connected to ground. Thus, the gate drive is referenced to ground. So by applying a voltage of >7V (for Power MOSFETs) or >4V (for Logic Level MOSFETs), the MOSFET can be fully turned on. Now let’s talk about the high-side c
Read more