Car (PM) Preoditic Maintenance,car maintenance schedule chart, car general service checklist, pms car service, periodic maintenance service maruti, general car service, car servicing guide, servicing your car, preventive and periodic maintenance

-

Car Preoditic Maintenence

         All cars/ vehicle need to a Preoditic Maintenence regularly for car health
  ** Check  all tyre pressure, 


 1.      Check brake padel for smooth braking
 2.      Check all light like Head light low b eam High beam and hazard and indicator,
 and brake bulb and reverse gear bulb etc
 3.Check engine oil level,  check brake oil
     level, check coolant level etc
4. If you do not use car regularly may be
    You used car monthly 1 or 2 day, so I
     recommended in between 3/4 or 5 day
    After start the vehicle only 20-30 minutes
   And off them, because if you don't use car regularly basis your car battery goes down
On any time and initially not started🙂
5. Finally car clean weekend one time weekly basic and engine compartment don't use high pressure water gun, because
 If you use high pressure water gun may be
 damage other part,. Use compressed air for
  cleaning  know more about car maintenance . know more about car maintenance best car maintenance tips.

      *If seen any abnormalities in your     car Visit the car dealer and solve them* 

            
 read more topic: how work car charging system on below link 

 read another topic : automobiletution.blogspot.com    
        

Comments

Post a Comment

Popular posts from this blog

Using the TLP250 Isolated MOSFET Driver - Explanation and Example Circuits

-
Image
I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well
Read more

N-Channel MOSFET High-Side Drive: When, Why and How?

-
Image
I had previously shown how to drive N-channel MOSFETs in low-side configuration. You can find the tutorial here: http://electel.blogspot.com/2016/12/low-side-mosfet-drive-circuits-and_23.html I’ve been requested to write a tutorial/article regarding high-side MOSFET drive. So, here I’ll talk about N-channel MOSFET high-side drive. Let’s first look at the common low side configuration.  Fig. 1 - N-channel MOSFET configured as low-side switch Now let’s look at a MOSFET configured as a high-side switch. Fig. 2 - N-channel MOSFET configured as high-side switch You can quite easily see the difference between the high-side configuration and the low-side configuration. In the low-side configuration, the load is connected between the drain and +V, while the source is connected to ground. Thus, the gate drive is referenced to ground. So by applying a voltage of >7V (for Power MOSFETs) or >4V (for Logic Level MOSFETs), the MOSFET can be fully turned on. Now let’s talk about the high-side c
Read more

Using the high-low side driver IR2110 - explanation and plenty of example circuits

-
Image
In many situations, we need to use MOSFETs configured as high-side switches. Many a times we need to use MOSFETs configured as high-side and low-side switches. Such as in bridge circuits. In half-bridge circuits, we have 1 high-side MOSFET and 1 low-side MOSFET. In full-bridge circuits we have 2 high-side MOSFETs and 2 low-side MOSFETs. In such situations, there is a need to use high-side drive circuitry alongside low-side drive circuitry. The most common way of driving MOSFETs in such cases is to use high-low side MOSFET drivers. Undoubtedly, the most popular such driver chip is the IR2110. And in this article/tutorial, I will talk about the IR2110. You can download the IR2110 datasheet from the IR website. Here's the download link: www.irf.com/product-info/datasheets/data/ir2110.pdf First let’s take a look at the block diagram and the pin assignments and pin definitions (also called lead assignments and lead definitions): Fig. 1 - IR2110 block diagram (click on image to enlarge)
Read more