White Smoke || Black smoke || Car Health Tips

-

White smoke || Black smoke




This is a more important part of all vehicle for road permit,because when you driving on street and traffic told about vehicle document and driving license of all your document are right but you not registered your car on emission control office these condition traffic police fine him this cause car emission system are more important for your car health and road traffic
Car Emission control system have a few many part are fitted for controlling the emission,example

  • Automobile Emission control system
           Catalytic converter
  •        EGR (Exhaust gas recirculation)
  •        Oxygen sensor
  •        Air fuel ratio sensor



Catalytic converter

  It is a part of all vehicle for burning exhaust gas out from car ,it is a cylindrical unit about the size of a small silencer and it installed into the exhaust system of a vehicle such as a car, scooter moped,motor cycle or auto rickshaw.it is pleased between the exhaust manifold and the silencer inside the converter there is a 🍯 honeycomb structure of a ceramic or metal which is coated with alumina base material and there after a second coating of precious metal platinum,paradium and rhodium or combination of the same.This second coating serves as a catalyst,a catalyst is a substance which causer a chemical reaction that normally does not happen in the given condition as a result of the catalytic reaction,when the exhaust gases pass over the converter substance toxic gasses dish as CO,HC & NOX are converted into harmless CO2,H2 and N2


THERE ARE TWO TYPE OF CATALYTIC CONVERTER


A 2way converter, which is used to control CO and HC emissions by oxidationA 3way converter,which is used almost in all petrol cars in control co and HC by oxidation as well asNOx by reduction

EGR

1)EGR is promising method of controlling NOx emission,EGR controlled 81-88%of NOx at 30% recycling

2) with 30%recycling there is a fuel penalty of 23.1%to 28%consedering minimum bsfc values for different speed percentage fuel penalty corresponding to minimum bsfc value increased from 3.85% to 28% when the percentage recycling increased from 10% to 30% .

3)with 30% recycling as the speed increased from 9% to 13.5% and from 1.88% to 13.5% in the recycling range of 10% to 30%  even with 20% recycling the loss is maximum power was high as 31.8% with running atb2400 RPM( Revolution per minute)

4)NOx emission is more on higher speed

5) the rate of reduction of NOx  emission is much faster at higher  speed with increase in present recycling🚙


EGR work on some exhaust gas received and mix with normal air which are  in combustion chamber,EGR use for better combustion because. EGR used hot air,it have a electronically controlled valve which are open  and close air tap  for help in better combustion

OXYGEN SENSOR

If any oxygen found on cat exhaust pipes then it's malfunction


AIR FUEL RATIO SENSOR

If  air fuel ratio high or low in 1to 3 second then this sensor are sending data to ECM
And ECM malfunction light glowing in car cluster meter

Comments

Post a Comment

Popular posts from this blog

N-Channel MOSFET High-Side Drive: When, Why and How?

-
Image
I had previously shown how to drive N-channel MOSFETs in low-side configuration. You can find the tutorial here: http://electel.blogspot.com/2016/12/low-side-mosfet-drive-circuits-and_23.html I’ve been requested to write a tutorial/article regarding high-side MOSFET drive. So, here I’ll talk about N-channel MOSFET high-side drive. Let’s first look at the common low side configuration.  Fig. 1 - N-channel MOSFET configured as low-side switch Now let’s look at a MOSFET configured as a high-side switch. Fig. 2 - N-channel MOSFET configured as high-side switch You can quite easily see the difference between the high-side configuration and the low-side configuration. In the low-side configuration, the load is connected between the drain and +V, while the source is connected to ground. Thus, the gate drive is referenced to ground. So by applying a voltage of >7V (for Power MOSFETs) or >4V (for Logic Level MOSFETs), the MOSFET can be fully turned on. Now let’s talk about the high-si...
Read more

Using the SG3525 PWM Controller - Explanation and Example: Circuit Diagram / Schematic of Push-Pull Converter

-
Image
PWM is used in all sorts of power control and converter circuits. Some common examples include motor control, DC-DC converters, DC-AC inverters and lamp dimmers. There are numerous PWM controllers available that make the use and application of PWM quite easy. One of the most popular of such controllers is the versatile and ubiquitous SG3525 produced by multiple manufacturers – ST Microelectronics, Fairchild Semiconductors, On Semiconductors, to name a few. SG3525 is used extensively in DC-DC converters, DC-AC inverters, home UPS systems, solar inverters, power supplies, battery chargers and numerous other applications. With proper understanding, you can soon start using SG3525 yourself in such applications or any other application really that demands PWM control. Before going on to the description and application, let’s first take a look at the block diagram and the pin layout. Pins 1 (Inverting Input) and 2 (Non Inverting Input) are the inputs to the on-board error amplifier. If you a...
Read more

Using the TLP250 Isolated MOSFET Driver - Explanation and Example Circuits

-
Image
I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well...
Read more