Car electric repair,What is vehicle repair,What is the name of someone who repairs cars,What does a motor mechanic do,Is auto mechanic a trade,

-

Electrical Diagonosis

Today I discussed with you some minor problem but mazor Diagnosis
I will discussed you because if you have a same problem You Can easy to solve them...

Problem is car electric fan motor continuously on when car is start?

When we car start then car electric fan motor not operate,if I on a/c system then operate.but either a/c off this fan not operate starting in between time.car electric fan motor voltage supply in two way one is
When we a/C start on vehicle
Another, when engine coolant tempareture high (thermostat valve open)
If you a/c on and fan not run,check this first, remove the fan motor fuse if burn
replace them second if ok remove the fan motor coupler start engine and a/c on and check with multimeter in DC 12 volt out on the coupler if volt out from them replace fan motor,because fan motor have a carbon brush these brush are low thickness for not touch in armeture/commutator.

Either condition electric fan motor run.

when car engine coolant temperature is more than standard level. Means engine thermostat valve opening start in (82°and fully open is94°)that time without a/c switch on these fan are running .

If car Electric fan is always run when start the car ,reason is engine coolant temperature sensor fault or cut the coolant tempareture sensor wiring harness,know more about car electrical repair

I think it help you.....
If any questions send me on comment box


See auto diagonosis

Comments

Post a Comment

Popular posts from this blog

Using the TLP250 Isolated MOSFET Driver - Explanation and Example Circuits

-
Image
I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well
Read more

N-Channel MOSFET High-Side Drive: When, Why and How?

-
Image
I had previously shown how to drive N-channel MOSFETs in low-side configuration. You can find the tutorial here: http://electel.blogspot.com/2016/12/low-side-mosfet-drive-circuits-and_23.html I’ve been requested to write a tutorial/article regarding high-side MOSFET drive. So, here I’ll talk about N-channel MOSFET high-side drive. Let’s first look at the common low side configuration.  Fig. 1 - N-channel MOSFET configured as low-side switch Now let’s look at a MOSFET configured as a high-side switch. Fig. 2 - N-channel MOSFET configured as high-side switch You can quite easily see the difference between the high-side configuration and the low-side configuration. In the low-side configuration, the load is connected between the drain and +V, while the source is connected to ground. Thus, the gate drive is referenced to ground. So by applying a voltage of >7V (for Power MOSFETs) or >4V (for Logic Level MOSFETs), the MOSFET can be fully turned on. Now let’s talk about the high-side c
Read more

Using the high-low side driver IR2110 - explanation and plenty of example circuits

-
Image
In many situations, we need to use MOSFETs configured as high-side switches. Many a times we need to use MOSFETs configured as high-side and low-side switches. Such as in bridge circuits. In half-bridge circuits, we have 1 high-side MOSFET and 1 low-side MOSFET. In full-bridge circuits we have 2 high-side MOSFETs and 2 low-side MOSFETs. In such situations, there is a need to use high-side drive circuitry alongside low-side drive circuitry. The most common way of driving MOSFETs in such cases is to use high-low side MOSFET drivers. Undoubtedly, the most popular such driver chip is the IR2110. And in this article/tutorial, I will talk about the IR2110. You can download the IR2110 datasheet from the IR website. Here's the download link: www.irf.com/product-info/datasheets/data/ir2110.pdf First let’s take a look at the block diagram and the pin assignments and pin definitions (also called lead assignments and lead definitions): Fig. 1 - IR2110 block diagram (click on image to enlarge)
Read more