car immobilizer reset || Car immobilizer system

-

Immobilizer system

Modern car have a immobilizer or key less entry system is used,because immobolizer system is a car security system which provide the company, without immobolizer system car not start, continuously crank but not start
If you enter the barrel unauthorized key while car not start because immobilizer ECU forward the Data from car ECM and ECM disconnect the fuel supply system🚙
It's have a some component

  • Immobilizer warning light
  • Immobilizer ECU
  • Immobilizer barrel switch


These any parts have a problem car immobilizer system warning light continuously blinking and car not start

IMMOBiLIZER WARNING LIGHT

It is part for warning you, if immobolizer ECU or amplifier have a any problem like rat kut the wiring or dirty part enter these part are also malfunction came through warning light constant blinking know more about Immobilizer full details


IMMOBILIZER ECU

Car all specific part have a one ECU so immobilizer have a ECU  this ECU all data send to car ECM 


  • IMMOBILIZER BARREL SWITCH


Barrel have a one switch like a amplifier which send data from barrel position to ECU  and then start the vehicle

Any problem an immobilizer system ECM create a code for symptom and then need to check

(All smart entry wireless remote lock unlock system have a specific id code registered and specific distance put in immobolizer system   If you off the car and all door closed and you out from car and door closed and your car remote inside a car,that situation smart entry system warned your remote is enter the car and door unlock automaticallyThis is a feature of smart entry system)
Read more 

Comments

Post a Comment

Popular posts from this blog

Using the TLP250 Isolated MOSFET Driver - Explanation and Example Circuits

-
Image
I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well
Read more

N-Channel MOSFET High-Side Drive: When, Why and How?

-
Image
I had previously shown how to drive N-channel MOSFETs in low-side configuration. You can find the tutorial here: http://electel.blogspot.com/2016/12/low-side-mosfet-drive-circuits-and_23.html I’ve been requested to write a tutorial/article regarding high-side MOSFET drive. So, here I’ll talk about N-channel MOSFET high-side drive. Let’s first look at the common low side configuration.  Fig. 1 - N-channel MOSFET configured as low-side switch Now let’s look at a MOSFET configured as a high-side switch. Fig. 2 - N-channel MOSFET configured as high-side switch You can quite easily see the difference between the high-side configuration and the low-side configuration. In the low-side configuration, the load is connected between the drain and +V, while the source is connected to ground. Thus, the gate drive is referenced to ground. So by applying a voltage of >7V (for Power MOSFETs) or >4V (for Logic Level MOSFETs), the MOSFET can be fully turned on. Now let’s talk about the high-side c
Read more

Using the high-low side driver IR2110 - explanation and plenty of example circuits

-
Image
In many situations, we need to use MOSFETs configured as high-side switches. Many a times we need to use MOSFETs configured as high-side and low-side switches. Such as in bridge circuits. In half-bridge circuits, we have 1 high-side MOSFET and 1 low-side MOSFET. In full-bridge circuits we have 2 high-side MOSFETs and 2 low-side MOSFETs. In such situations, there is a need to use high-side drive circuitry alongside low-side drive circuitry. The most common way of driving MOSFETs in such cases is to use high-low side MOSFET drivers. Undoubtedly, the most popular such driver chip is the IR2110. And in this article/tutorial, I will talk about the IR2110. You can download the IR2110 datasheet from the IR website. Here's the download link: www.irf.com/product-info/datasheets/data/ir2110.pdf First let’s take a look at the block diagram and the pin assignments and pin definitions (also called lead assignments and lead definitions): Fig. 1 - IR2110 block diagram (click on image to enlarge)
Read more