The First Lotus Elite Design

-
I last wrote about Lotus five years ago in this post dealing with the Lotus Elan. But to me and many others, the classic Lotus was the original Lotus Elite produced 1957-1963.

Its design has been credited to Peter Kirwan-Taylor (1930-2014) (reference here), but some attribute major input to Ron Hickman (who also contributed to the Elan). The Revs Institute in Naples, Florida has a second-series 1962 Lotus in its collection and its Web page gives credit largely to Kirwan-Taylor while acknowledging contributions by Hickman.

Regardless of its styling pedigree, the original Elite was an outstanding design, as can be seen in the images below.

Gallery

A 1959 Lotus Elite, Coys Auction photo.

Many Elites were painted cream color as in the first image.  Buy here is a 1963 Lotus in not-quite British Racing Green: Hyman auctions photo.

This and the following images of a 1962 Lotus Elite are Bonhams auction photos.  The design is simple, logical, and essentially ornamentation-free.  By "logical," note the aft cut line of the door as it extends from the door sill up into the greenhouse in one straight line.  The back window is large and curved, so there is no real need for quarter windows in the greenhouse.  The car's rear is chopped, with some radius work to soften the transition.

In profile, the Elite has a classically long hood line, the driver's head being well aft of the car's center.  The slope of the windshield is greater than seen on contemporary American cars.  A subtle point has to do with the wheel openings.  The forward opening is nearly round, but slightly flattened at the top -- this having to do with the shape of the fender relative to the fenderline profile.  The rear opening is essentially squared-off.  Were it shaped like the front opening, a visually "busy" zone would have been created due to the proximity with the windows and aft quarter pillar.  Another subtlety is the slight rise in the fenderline above the rear axle that gives that line a whiff of variety.

Frontal view showing the curved, one-piece windshield.  The grille opening is just that: an opening.  Bumpers are flimsy and not well mated to the grille, perhaps the design's weakest point, albeit a trivial one.

Rear quarter view.  Nothing to criticize here.

Comments

Post a Comment

Popular posts from this blog

N-Channel MOSFET High-Side Drive: When, Why and How?

-
Image
I had previously shown how to drive N-channel MOSFETs in low-side configuration. You can find the tutorial here: http://electel.blogspot.com/2016/12/low-side-mosfet-drive-circuits-and_23.html I’ve been requested to write a tutorial/article regarding high-side MOSFET drive. So, here I’ll talk about N-channel MOSFET high-side drive. Let’s first look at the common low side configuration.  Fig. 1 - N-channel MOSFET configured as low-side switch Now let’s look at a MOSFET configured as a high-side switch. Fig. 2 - N-channel MOSFET configured as high-side switch You can quite easily see the difference between the high-side configuration and the low-side configuration. In the low-side configuration, the load is connected between the drain and +V, while the source is connected to ground. Thus, the gate drive is referenced to ground. So by applying a voltage of >7V (for Power MOSFETs) or >4V (for Logic Level MOSFETs), the MOSFET can be fully turned on. Now let’s talk about the high-si...
Read more

Using the high-low side driver IR2110 - explanation and plenty of example circuits

-
Image
In many situations, we need to use MOSFETs configured as high-side switches. Many a times we need to use MOSFETs configured as high-side and low-side switches. Such as in bridge circuits. In half-bridge circuits, we have 1 high-side MOSFET and 1 low-side MOSFET. In full-bridge circuits we have 2 high-side MOSFETs and 2 low-side MOSFETs. In such situations, there is a need to use high-side drive circuitry alongside low-side drive circuitry. The most common way of driving MOSFETs in such cases is to use high-low side MOSFET drivers. Undoubtedly, the most popular such driver chip is the IR2110. And in this article/tutorial, I will talk about the IR2110. You can download the IR2110 datasheet from the IR website. Here's the download link: www.irf.com/product-info/datasheets/data/ir2110.pdf First let’s take a look at the block diagram and the pin assignments and pin definitions (also called lead assignments and lead definitions): Fig. 1 - IR2110 block diagram (click on image to enlarge)...
Read more

Using the SG3525 PWM Controller - Explanation and Example: Circuit Diagram / Schematic of Push-Pull Converter

-
Image
PWM is used in all sorts of power control and converter circuits. Some common examples include motor control, DC-DC converters, DC-AC inverters and lamp dimmers. There are numerous PWM controllers available that make the use and application of PWM quite easy. One of the most popular of such controllers is the versatile and ubiquitous SG3525 produced by multiple manufacturers – ST Microelectronics, Fairchild Semiconductors, On Semiconductors, to name a few. SG3525 is used extensively in DC-DC converters, DC-AC inverters, home UPS systems, solar inverters, power supplies, battery chargers and numerous other applications. With proper understanding, you can soon start using SG3525 yourself in such applications or any other application really that demands PWM control. Before going on to the description and application, let’s first take a look at the block diagram and the pin layout. Pins 1 (Inverting Input) and 2 (Non Inverting Input) are the inputs to the on-board error amplifier. If you a...
Read more