Cluster meter description

-

Vehicle cluster metre

  Many vehicle have many type of cluster
  Meter design basic,cluster metre is basically have a four (4) part 
      1) RPM(Revolution per mitre) metre
      2) kmpl ( kilo metre per hour) metre
      3) Fuel metre
      4)Engine coolant tempareture metre

 RPM means vehicle engine crankshaft 
 Revolution per minute, may be 1000/2000/
 3000/4000 etc

  Cluster metre very important part for car internal health🙂


 

Modern vehicle cluster metre are also modern or smart digital type,.it's have a (MID) Multi information display for allo
Cared digitally for your car actually problem🙂

 Its Iave a more (MIL=Malfunction indication light)

    1.Engine check light🚙
    2.Glow plug light (for diesel vehicle)🚙
    3.Sit belt warning light🚙
    4.Hand brake warning light🚙
    5.Immobolizer warning light🚙
    6.Srs light🚙
    7.Timing belt warning light (if vehicle 
        have a belt drive)🚙
    8.Engine oil level warning light🚙
    9.Engine oil pressure warning light🚙
   10.Abs warning light🚙
   11.Head light high beam light🚙
   12.Battery charging light🚙
   13.Ambient tempareture light🚙
   14.clock🚙
   15.Tyre.pressure warning light🚙
   16.Door open warning light🚙
   17.Hazard warning light🚙
   18.over heating warning light🚙
   19.steering warning light (EPs=
         Electronic power steering)🚙
   20.service warning light🚙
    

 Cluster metre all light are warning the 
  car  for problem🙂
car all  check light have a different type each check light have a each type of problem indicate,check light ia a symbol for car specific problem for easy to determined the problem for solve when car indicate a check light that time first visit the car authorised dealer as soon as possible,

Comments

Post a Comment

Popular posts from this blog

Using the TLP250 Isolated MOSFET Driver - Explanation and Example Circuits

-
Image
I’ve already shown how to drive an N-channel MOSFET (or even an IGBT) in both high-side and low-side configurations in a multitude of ways. I’ve also explained the principles of driving the MOSFETs in these configurations. The dedicated drivers I’ve shown so far are the TC427 and IR2110. Some people have requested me to write up on MOSFET drive using the very popular TLP250. And I’ll explain that here. The TLP250, like any driver, has an input stage, an output stage and a power supply connection. What’s special about the TLP250 is that the TLP250 is an optically isolated driver, meaning that the input and output are “optically isolated”. The isolation is optical – the input stage is an LED and the receiving output stage is light sensitive (think “photodetector”). Before delving any further, let’s look at the pin configuration and the truth table. Fig. 1 - TLP250 Pin Configuration Fig. 2 - TLP250 Truth Table Fig. 1 clearly shows the input LED side and the receiving photodetector as well
Read more

N-Channel MOSFET High-Side Drive: When, Why and How?

-
Image
I had previously shown how to drive N-channel MOSFETs in low-side configuration. You can find the tutorial here: http://electel.blogspot.com/2016/12/low-side-mosfet-drive-circuits-and_23.html I’ve been requested to write a tutorial/article regarding high-side MOSFET drive. So, here I’ll talk about N-channel MOSFET high-side drive. Let’s first look at the common low side configuration.  Fig. 1 - N-channel MOSFET configured as low-side switch Now let’s look at a MOSFET configured as a high-side switch. Fig. 2 - N-channel MOSFET configured as high-side switch You can quite easily see the difference between the high-side configuration and the low-side configuration. In the low-side configuration, the load is connected between the drain and +V, while the source is connected to ground. Thus, the gate drive is referenced to ground. So by applying a voltage of >7V (for Power MOSFETs) or >4V (for Logic Level MOSFETs), the MOSFET can be fully turned on. Now let’s talk about the high-side c
Read more

Using the high-low side driver IR2110 - explanation and plenty of example circuits

-
Image
In many situations, we need to use MOSFETs configured as high-side switches. Many a times we need to use MOSFETs configured as high-side and low-side switches. Such as in bridge circuits. In half-bridge circuits, we have 1 high-side MOSFET and 1 low-side MOSFET. In full-bridge circuits we have 2 high-side MOSFETs and 2 low-side MOSFETs. In such situations, there is a need to use high-side drive circuitry alongside low-side drive circuitry. The most common way of driving MOSFETs in such cases is to use high-low side MOSFET drivers. Undoubtedly, the most popular such driver chip is the IR2110. And in this article/tutorial, I will talk about the IR2110. You can download the IR2110 datasheet from the IR website. Here's the download link: www.irf.com/product-info/datasheets/data/ir2110.pdf First let’s take a look at the block diagram and the pin assignments and pin definitions (also called lead assignments and lead definitions): Fig. 1 - IR2110 block diagram (click on image to enlarge)
Read more